The Nimbus WiMi6220 Wireless System Bundle V-Mountfrom Nimbus WiMi6220 Wireless System Bundle V-Mountpairs with an optional WiMi6220 receiver as a point-to-point Wi-Fi transmission system with a 4921' range and only 80ms latency. With both units featuring built-in 5 GHz Wi-Fi, no additional network connection is required. This model can be powered using the included V-mount battery plate or via the 2-pin LEMO power connector for continuous power.

The transmitter encodes and sends up to a 1080p60 SDI or HDMI signal as an H.264 encoded signal, and the receiver decodes and outputs it as video. The transmitter is also capable of multicasting to up to four receivers at the same time over the same range and with the same near-zero delay.

An Ethernet port, which allows for CCU/PTZ camera control, can also be used for wired connectivity and 1080p60 transmission to the receiver via Cat 5e cable. The WiMi6220 transmitter also features an RS-422 interface and a two-way talk-back audio jack. With a corresponding audio jack available on the receiver, the talk-back port allows connecting a headset mic for communicating with talent. The WiMi6220 transmitter offers a 1/4"-20 mounting thread on the bottom.

1 x 3G-SDI/HDMI Transmitter/Encoder    2 x 3G-SDI/HDMI Receiver/Decoders    4921' Range over 5 GHz Wi-Fi    Up to 1080p60 Video Signals, H.264 Codec    V-Mount Battery Plates on Each Unit    Power Adapters, RJ45 Adapter for RS-422

• 4921' range over 5 GHz Wi-Fi
• 80ms latency
• Includes V-mount battery plate
• Encodes and sends up to a 1080p60 SDI or HDMI signal in H.264 MPEG-4 Parts 10: AVC (decoded by optional receiver)
• RTSP streaming server (RTP/UDP)
• MPEG2TS streaming (UDP)
• 3G/HD/SD-SDI and HDMI inputs
• Ethernet port for CCU/PTZ control or wired connectivity and 1080p60 transmission
• Two-way talk-back audio jack for headset mic communication
• RS-422 interface
• Baseline profile with level 4.2
• 2-pin LEMO power input
• USB firmware update port
• 1/4"-20 mounting thread

Related Questions and Answers

Q: 1. can i use this on a devin graham glidecam and a jib? also, can you reccomend the kind of cables i need if i were to use this on a 8ft jib. thanks

A: Hi Divine - yes, it should work fine! we don't have direct experience with the glidecam, but many customers use it with steadicam, which works the same. Remember you'll need a small lightweight battery, check out our new lp-e6 battery adapter, which is about to be released (you will want to ask for part number 2-178-0001)this bundle is great for that. For a jib you'll want a longer cable, which we can make to size, but you will need to contact us at redrock micro direct for that cable. Everything else is available here.

Q: 2. Will this work with the ARRI Skypanl?

A: It's work but the signal very week and not stable at all

Q: 3. Are the FLEXcables included?

A: The cables pictured are included.

Q: 4. Do you still need a battery pack of some kind to power it? If so what's the cheapest and lightest battery option?

A: Hi Dane - yes the microRemote does require power from an external source. You have a lot of options hereIf you are using an existing gimbal, you can often tap into the power provided from the gimbal's lipo battery (make sure you have the correct cable there). DJI, Freefly, and Letus are among the options thereif you need a standalone battery, you can use any p-tap compatible 12-14.4v battery. We often recommend switronix powerBase (there are many options, make sure to choose the one that is right for you) or a swit battery for sony camcorders with built-in p-tap like this one a href= http://www.bhphotovideo.com/c/product/1027696-REG/swit_s_8u63_li_ion_rechargeable_battery.html target= _blank http://www.bhphotovideo.com/c/product/1027696-REG/swit_s_8u63_li_ion_rechargeable_battery.html/ayou can also ask any BH representative for a battery solution that is 12-18vDC, has a built-in p-tap battery source, and does not require a plate to use. Hope that helps

Q: 5. Is it compatible with canon 5d Mark III?

A: Yes, the microRemote is compatible with Canon still cameras including the 5D MK III. if you are using canon L-series lenses, you will want to make sure and get lens gears as well. A good starter kit for virtually all lens sizes is here: a href= http://www.bhphotovideo.com/c/product/748784-REG/Redrock_Micro_8_003_0107_microLensGears_Kit_4.html target= _blank http://www.bhphotovideo.com/c/product/748784-REG/Redrock_Micro_8_003_0107_microLensGears_Kit_4.html/a

Q: 6. Would this fit on a contax G1?

A: Yes, the smaller size should work with the G1.

Q: 7. How much Wireless DMX Transmitter needs to turn 16 lights ?How much Wireless DMX ReceiverNeed to turn 16 lights ?Tank you!

A: If you are using a lighting control board, you can connect one transmitter to the output and one receiver to the first light in your chain. Then, you can daisy chain the remaining lights together. So, one receiver and one transmitter should be enough, unless you are using all your lights far away from each other and don't want to have any cables. In that case, each light would need both a receiver (to get the signal from the previous unit) and a transmitter (to send it to the next unit in the sequence).

Q: 8. I see that the basestation is wireless ready , does that mean it will connect and work with the handheld wireless remote?

A: Hi Anthony - yes that is correct. just add this hand unit (you can purchase it later) and its ready for wireless:a href= http://www.bhphotovideo.com/c/product/1014379-REG/redrock_micro_3_114_0001_microremote_handheld_wireless_focus.html target= _blank http://www.bhphotovideo.com/c/product/1014379-REG/redrock_micro_3_114_0001_microremote_handheld_wireless_focus.html/aplease note the picture of the hand unit is outdated - the new version is slimmer and smaller

Q: 9. Does it come with the r2 or does that have to be bought separately?

A: Hi! The R2 sled as R2 bundle don't include the Ronin R2.

Q: 10. can you order this kit with the collins clamp so you can clamp the finger wheel to the movi m5?

A: Hi and thanks for the question. Yes you can absolutely order a collins clamp and swap out the ring connector with the collins clamp. If you have any questions on how to do that just drop us a line at support@redrockmicro.comHope that helps