Maximize the transfer speeds of your compatible fiber optic connections with the QNAP 25G SFP28 LC Optical Transceiverfrom QNAP. This SFP28 optical transceiver features full duplex LC connectors and is designed to deliver up to 25 Gb/s transfer speeds across 328' using fiber cables on the 850nm wavelength. Integrating this module into your data center, campus, or enterprise network provides reliable, high-bandwidth connections with compatible devices.

LC to LC Connection    SFP28 Optical Transceiver    25 Gb/s Throughput    Supports 850nm Wavelength    328' Range

Related Questions and Answers

Q: 1. Does this product work with TTL for Nikon cameras?

A: The PlusX units are not TTL. For TTL, you would need the Flex and Mini units from PocketWizard (#WIFTT5N and #WIMTT1N).

Q: 2. Will the Plus X work with the Samsung NX 20 as a flash trigger for off camera flash units?

A: Yes, but you have to have another unit for your off camera flash unit. These units act as both a receiver and transmitter. One is attached to your camera's hot shoe and another is attached to your flash via PC cable.

Q: 3. Are these compatible with Profoto and if so, do I need to order any other sync cords?

A: Yes, the Pocketwizard PlusX is compatible with most of the Profoto line.You will need a PlusX for each Profoto and one for your camera. It comes with a sync cord with adapters so you can use it without the need of other sync cords.Note the PlusX is a manual sync so it will sync the strobe, but it is not TTL or have the ability to change power from the camera.

Q: 4. Will this works with older profoto pack with integrated pocketwizard?

A: Yes this unit is backwards compatible with built in Pocket Wizard receivers found in many Profoto power packs or monolights.

Q: 5. So in essence, with the right breakout cables (QSFP28 to 4 x SFP28) the switch can support 24 (4x4 + 8) SFP28 ports?

A: The QNAP QSW-M7308R-4X 12-Port 100G QSFP28 / 25G SFP28 Managed Network Switch, B&H # QNQSWM7308R4, does not support breakout cables.

Q: 6. How's the fan noise? Looking for a 10G switch, but it'll be in a room where noise is a problem.

A: The fan on the Ubiquiti Networks Switch Enterprise XG 24 24-Port 10G Managed Network Switch with 25G SFP28 is very silent.

Q: 7. Would these work on Leica SL-2S to trigger an Elinchrom Five?

A: Yes, the PocketWizard Plus X 2 Pack would work on the Leica SL2-S Mirrorless Camera and would trigger an Elinchrom FIVE Monolight Kit.

Q: 8. Can two PlusX (transmitter) trigger 1 PlusX (receiver) simultaneously without interfering? A situation when the 2nd shooter is also using 2nd transmitter to trigger the same strobe the first shooter is triggering ?

A: If you've got two photographers in the same studio, each with a PlusX transceiver on their camera (set to the same channel), they can both trigger the strobes. The receiver doesn't care where the signal comes from, just that it's the right frequency. The limiting factor will be the recycle rate of the lighting units (which can be a few seconds, depending on their settings) so if you both try to trigger the strobes at the same exact time, they'll only fire once.

Q: 9. Is secondary power supply available?

A: No, the Ubiquiti Networks Switch Enterprise XG 24 24-Port 10G Managed Network Switch with 25G SFP28 does not support the option for a secondary internal power supply.

Q: 10. I have 3 Mettle 600AD Monolights, they have slave units built in, How many Pocket Wizards Xs do I need? I have Nikon D5300 and. Sekonic L-478DR flash meter

A: If you have three monolights and one camera, you will need a total of 4 units. One unit would be a transmitter on your D5300 while each monolight would connect to Plus X unit to receiver the signal. Your Sekonic L-478DR would be able to trigger the flashes with the Plus X units attached to take your flash reading.