Constructed of chrome-plated steel, the Kupo Mitchell Round Mounting Plate 1 1/8" Junior Receiverfrom Kupo Mitchell Round Mounting Plate 1 1/8" Junior Receivercan be used for custom mounting solutions on your set. This plate has a male Mitchell plate on one side and a 1 1/8" Junior receiver on the other. It comes with a castle nut and four stainless steel spacers for adapting the fit of the Mitchell plate.

Welded 1 1/8" (28mm) Junior Receiver    Male Mitchell Base with Castle Nut    Chrome-Plated Steel Construction    4 x Stainless Steel Spacers

Constructed of durable chrome-plated steel

Adapts a Mitchell threaded collar to a 1 1/8" Junior receiver

The Junior receiver is welded onto the Mitchell plate for durability

A castle nut and four spacers are included for mounting the adapter

Related Questions and Answers

Q: 1. Can the 1/4" thread be replaced with a 3/8" thread? I prefer to not use an adapter.

A: Unfortunately, we do not have a super grip finger option that has a built-in 3/8"-16 male screw. As an alternative, I would recommend purchasing the Impact Heavy-Duty Swivel Pin, B&H # IMSRP118, and the Kupo Baby Ball Head Adapter, B&H # KUKG014212, as an alternative for your usage needs.

Q: 2. What is the diameter of the camera plate?

A: The base mount diameter on the Kupo Super Grip Finger with Round Camera Plate is 60mm.

Q: 3. what is the weight capacity when used for a monitor on set? of course on a c stand....

A: Kupo states that the Kupo VESA Monitor Mounting Plate with 5/8- Baby Pin "...is designed for any monitor that comes with a VESA mounting 75mm x 75mm or 100mm x 100mm." We would recommend a payload of 22kg (48.5 lbs) or less, as comparable Kupo mounts suggest.

Q: 4. How tall of a ceiling do you need to extend this boom arm out to set it in place? With wheels attached.

A: The boom part on the Kupo 546M K Stand Junior Boom Stand can be set into position with the stand at the lowest setting and then extended. Working with at least a 7 foot ceiling would be good; the minimum working height is 65.4"/166cm.

Q: 5. How tall is this?

A: The Kupo Super Grip Finger with Round Camera Plate is 6.02 inches tall.

Q: 6. Would this support the weight an aputure LS600x with a soft box or lantern modifier at full extension?

A: The Lload apacity at Maximum extension for the 546M K Junior Boom stand is 17.6 lb. The LS600x weighs about 10.34lbs as long as your modifier is at or under 7.5lbs it will support both yes.

Q: 7. Will Matthews C-Plus C-stand or other brands fir in the 2K kupos receiver -- because they don't fit in the Kupos runway base stands??

A: The Kupo Mitchell Round Mounting Plate with 1 1/8" Junior Receiver should accept 1 1/8" junior pins.

Q: 8. Is the castle nut and bolt included?

A: The Kupo Mitchell Mount Cheese Plate (10 x 10 x .5") will not include castle nut or bolts.

Q: 9. Would two of these be secure enough to hold a slider on stands? Thinking they might allow different stand heights, for slider to be inclined. Regular Kupo ball head adapters would need to both be level. Not sure if these would cause instability or want to flop over to one side or other because of weight.

A: Yes. But would suggest the following for a better experience. Just add a washer with a 2 inch diameter Impact Rapid Baby to 1/4"-20 Male Threaded Adapter BH #IMCA101 • MFR #CA-101 https://bhpho.to/3DMiFXY

Q: 10. what is the max extention on the boom arm?

A: The boom arm of the Kupo Junior Boom Roller Stand (B&H# KUKS301512) at longer extensions will typically require a counterweight (e.g. a sandbag like B&H# IMSBFO15) and the degree to which it may be extended will vary by the relative distances from the point at which it attaches to the stand and those of the counterweight, on the one hand, and light (or other addition), on the other. Although the boom arm is about 60" long when fully extended, it should not be used at full extension and counterweighting is essential.