This 100' Genustech 6G-SDI 4K BNC Coaxial Cable 100ft Male-to-Malefrom Genustech 6G-SDI 4K BNC Coaxial Cable 100ft Male-to-Maleis compatible with video signals up to 6G-SDI 4K. Each end of this coaxial cable has a male BNC connector with a gold-plated pin.

RG6/18 AWG Coaxial SDI Cable    100' Length    BNC Male Connectors/Gold-Plated Pins    For 6G-SDI, HD-SDI & SD-SDI Signals

100' 6G-SDI coaxial cable

Male BNC connector with a gold pin on each end

Related Questions and Answers

Q: 1. Can this accept a DCI 4K RAW signal and down convert to 1080p?

A: No. It does not downconvert. It only converts the 4K signal from SDI to HDMI

Q: 2. Does the Blackmagic Design Mini Converter 6G-SDI to HDMI 4K up/down-convert? Will it accept 2160p29.97 via SDI and down-convert to 1080p29.97 or even 720p29.97 to the HDMI out?

A: This will take the 2160 29.97 signal and down convert to 1080p 29.97 or 720p 29.97.

Q: 3. can I use this cable to conect Osmo pocket3 to a Ninja screen recorder?

A: The Pearstone USB Type-C Male to HDMI Male 4K Cable (3'), BH # PECHD3, will physically connect both devices but will not transmit a video and audio signal to the recorder.

Q: 4. Looking to monitor 4k raw footage from bmpc to ikan d7 monitor. Will this do the trick even if the Ikan's max res is FullHD 1280?

A: If your Ikan d7 has an HDMI input then yes it will. It works great. The big down side is there is no way to mount it to anything, ie a 1/4 20 thread, and the need to power it. If you choose to power it over D-tap the power cable can run you $60. Looking back I wish I would of purchased a Wooden Camera C-box instead.

Q: 5. Can the audio be embedded to the HDMI output?

A: Whatever audio is on the SDI line will output over the HDMI. If you are looking to combine a video source with a different audio source you will want an audio to SDI miniconverter which allows you to embed up to 8 channels of audio onto a SDI line. You could then feed that SDI line into a SDI to HDMI miniconverter.

Q: 6. Is this backwards compatible with older Blackmagic Video Assist models? For example, could this cable connect a RED Komodo 12G-SDI output to a Blackmagic Video Assist with a 6G-SDI input?

A: The Blackmagic Design Micro BNC to BNC Male Cable for Video Assist (27.6") would not be compatible with the Blackmagic Video Assist with 6G-SDI input due to the Mini DIN connectors that model used.

Q: 7. Can a non 4k mini converter be used with a black magic 4k switcher? I'm not running the switcher at 4k quality, i.e. Black magic 1me 4k sending 1080i sdi to black magic sdi to analog mini converter (non 4k).

A: As long as you set the switcher to all inputs 1080i there should be no problem.

Q: 8. The spec says 12V. What is the actual input voltage range?

A: 12-31 Volts. Best to keep it closer to 12V to reduce heat.

Q: 9. How do you disconnect

A: To disconnect the Blackmagic Design Micro BNC to BNC Male Cable for Video Assist (27.6"), you'll need to twist and pull the BNC connector.

Q: 10. Is there any time delay from the processing?

A: When converting to the same resolution and frame rate, there should be no noticeable delay. Usually measured in microseconds. Products that are scaling up or down or changing frame rates, will always have some delay of a frame or more depending on the type of processing.