The 50' BZBGEAR Ultra-High Speed HDMI Cable with Ethernet 50'is an HDMI 2.1-capable active optical cable and is HDCP 2.2-certified to support UHD video resolutions up to 8K @ 60 Hz as well as 4K @ 120 Hz with bandwidth speeds up to 48 Gb/s. With its ability to draw power from a connected device, this fiber optic cable doesn't require an additional power source, allowing it to extend the HDMI signal much further than a standard HDMI cable. This cable supports multichannel audio including DTS-HD Master Audio and Dolby True HD signals as well as HEAC (HDMI Ethernet), ARC (Audio Return Channel), and HDR (High Dynamic Range).

Supports 8K UHD, HDR, ARC, 3D    HDMI 2.1 & HDCP 2.2 Support    Directional Design

• HEAC, ARC, and HDR support
• HDCP 2.2 certified
• DTS-HD Master Audio and Dolby True HD signals
• Support 8K UHD @ 120 Hz, 4K UHD @ 60 Hz, Full HD, 3D, Ethernet, Audio Return Channel, HDR 4:4:4 color format, and 48 bit/px color depth
• Optical fiber HDMI cable delivers with no delay

Related Questions and Answers

Q: 1. Does this cine version have the same focus breathing issue that the still lens version has?

A: These lenses will exhibit some breathing.

Q: 2. Has anyone used this lens with a Metabones Ultra 0.71 on a GH5? What were your results? Was focus clear and stable throughout zoom range? Did you have any vignetting? Thank you!

A: While we have not heard of this particular combination, it is an EF lens, a Metabones adapter, and a GH5 camera. And there are thousands of successful combinations of these components. We would expect this to work as intended with excellent sharpness.

Q: 3. Does this cable support 4k 60fps? The description mentions support for a 60hz refresh rate, but not 60fps in 4k.

A: Based on the specs, it does. In the overview, it says "supports resolutions up to 4K UHD @ 60 Hz."

Q: 4. The description says that auto-switching is supported. How does this work? As such, is the IR remote required to change the in

A: You could work with the front Input button on the BZBgear 4X1 8K UHD ULTRA SLIM HDMI 2.1 SWITCHER (8K60, 4K120HZ 4:4:4 10BIT) to control Auto-Switching. INPUT button ▪ Short press this button to circularly select signal source. ▪ Long press this button for 3 seconds to enable the auto switching mode. Pg7 Manual: https://bhpho.to/4aB5x8o

Q: 5. Could you mount this on a 5DIV for taking still images?

A: We're afraid not. This lens only covers up to a Super 35mm sensor, it will not cover the Full Frame of the 5D Mark IV.

Q: 6. There is a typo in the first line of the description?

A: There was error and we have since corrected it. We thank you for pointing this out and apologize for any confusion.

Q: 7. Does support Sony A7IV ?

A: The SmallRig 2956 Ultra-Slim HDMI Cable (13.8") BH #SM2956 will support the Sony a7 IV Mirrorless Camera BH #SOA74.

Q: 8. IF I buy in EF mount, can I change it the PL later on? How much would the switch be?

A: I believe not

Q: 9. Can this be used for microphone RF?

A: No, it is not recommended that you use an RG-6 cable like the Comprehensive Pro A/V / IT RG-6 High-Resolution RF Coaxial Cable (50') for microphone RF; because of the difference in impedance, you would need a 50-ohm cable like the Shure BNC Antenna Cable (100-foot), B&H # SHUA8100.

Q: 10. Can you display 4 different outputs? Like watch 4 different football games on each tv.

A: No, The BZBGear 2x2 4K60 HDMI Video Wall Controller with Audio has only one input and would only support one input signal. However, This HDMI 4 x 4 would allow you to have 4 input sources and be able to output to 4 Televisions. MuxLab 4x4 4K60 HDMI Matrix Switch BH #MU100508 https://bhpho.to/3GxJoM9