Switch among up to four instruments on stage with the Radial JX42 V2 Guitar & Amp Switcher. Not only can this rackmounted unit accommodate four instruments, it can also switch between two amplifiers, allowing you to change your tone on stage with the press of a button, or affording you an entirely mirrored backup system should you blow out your main amp on stage.

As this is a Radial product, you can rest assured that it has been engineered to give you a high-fidelity signal path, one that won't degrade the sound of your instruments or your amplifiers. This is made possible by Class-A circuitry and Jensen output transformers. With its built-in 120/240V power supply, the JX42 will work all over the globe. It can be integrated with a MIDI setup, and is also compatible with select Radial footswitches.

Switch between 2 Amps on Stage    Switch among 4 Instruments on Stage    High-Fidelity Signal Path    Silent Switching    Built-In Tuner Outputs    Worldwide Power Supply for World Tours    Compatible with MIDI Setups    Works with Select Radial Footswitches

Instantly switch among amplifiers on stage without signal coloration or additional noise. How? Class-A signal buffers preserve the tone of your instruments, with four inputs accessible on either the front or back panel of the JX42. Large backlit on/off switches select the active input, with the ability to have multiple instruments active simultaneously. 

The two amplifier outputs can feed separate amps and switch between the two, or you can use them to create a redundant system with the ability to switch to the backup at the press of a button.

Both outputs are isolated with premium Jensen transformers for exceptional audio quality, and feature ground lift switches to eliminate hum and buzz when connected to multiple amplifiers.

Switching between the two outputs is silent and free of pops or clicks to avoid any disruption to the performance.

The JX42 V2 is compatible with the Radial JR-2 footswitches, which allow you to remotely switch between the amp outputs or mute both as needed.

Inactive inputs feed a pair of always-on tuner outputs, which are buffered and mirrored on the front and back panels.

Remote control over the inputs is available with the optional JR-5 footswitch for hands-free operation, or by using your favorite MIDI controller.

Related Questions and Answers

Q: 1. Maximum Cat5 cable length?

A: Hello John,Thank you for your interest in Radial. Using shielded Cat5e cable, we have successfully tested lengths of 100 meters (328 ft) without signal loss. Regards,Ryan

Q: 2. These screws came up on a google search for "Canon 17-120 Cine-Servo Replacement Screw". Looks like it may work due to the thread type but can anyone confirm?

A: The thread type on these screws is 440.

Q: 3. Does the EQ effect the overall output, or just the mic or laptop audio?

A: The EQ controls on the Radial Engineering Presenter Mixer affect the microphone signal only.

Q: 4. Will this allow me to switch between two simple camcorders (Sony HDR-CX405) and send the signal to a monitor?

A: Yes, the Kopul HDMI 2.0 5 x 1 Switcher would allow you to connect up to five HDMI sources, and toggle between the connected sources. You could output this to an HDMI monitor.

Q: 5. Will this item be good for my mackie dlz creator for the background like noise hum as well i have shure sm7db and pig hog cable?

A: The Radial Engineering IceCube IC-1 Balanced Line Isolator and Hum Eliminator will not eliminate background noise, but it can remove or reduce humming sounds caused by grounding issues.

Q: 6. Doe this item work with a Catapult Mini TX on the one side and a Catapult Mini RX on the end with this item in the middle?

A: It is our understanding that the Radial Engineering Catapult RX4 Cat 5Snake for Audio/AES Routing (Receiver) does a variety of configurations. This includes TX on one side and RX on the other.

Q: 7. what are the thread specs? ( do they match typical 19 rack threads? )...

A: Hello Dennis,The ThumbSet screws are 4-40 type and are specific for mounting 500 series modules into our Workhorse power racks - they are too small to mount standard 19 equipment into equipment racks.Regards,Ryan

Q: 8. Are all the audio outputs simultaneous on output 4?

A: We are not sure of what is being asked. We can say that this is a matrix switcher, so whatever source you select on whatever output will also transfer the audio. However, it will not output all inputted audio streams to 1 output, if that is what you are asking. If you have further questions, please write us with further detail. provideo@bhphoto.com.

Q: 9. Does this version send a beep through the audio output when it's in pairing mode/when it loses signal with the device? The first version did, hoping this one solved that.

A: No, the Radial Engineering BT-PRO V2 Stereo Bluetooth Direct Box does not send any beep or chime sounds through the audio output when it is in pairing mode or if it loses Bluetooth signal with the device it is connected to.

Q: 10. Does this unit work standalone or does it have to be used with the Broadcast Press Box?

A: This broadcast audio splitter can be used a stand-alone unit, and only requires a balanced XLR input from a mixing board or other source. .