The Kramer Plenum-Rated Active Optical DisplayPort Cable 230ftfeatures high resolution and data transfer rate. The cable is thin and flexible. It also does not require external power. The user experience is maximized with integrator-oriented features and the latest advances in DisplayPort 1.4 technology.

DisplayPort Male Connector on Each End    Supports up to 8K @ 60 Hz Resolution    No External Power Required    Up to 32.4 Gb/s Data Transfer Rate

Supports 3D, HDCP, EDID, HBR3, DSC, and 8K @ 60 Hz resolution

Supports up to 8K @ 60 Hz over long cable runs without the need for an external power supply or additional extenders

Up to 32.4 Gb/s data rate with 8.1 Gb/s/lane (HBR3) link rate

Supports up to 8 channels of 16 or 24 bits linear PCM and 32 to 192 kHz sampling rate

Powers the active units via the DisplayPort connector

4.8mm diameter

Low smoke & halogen free

RoHS 2011/65/EU compliant, CE/FCC

Related Questions and Answers

Q: 1. Can I use this with USB 2.0 Mini-B 8 pin Tether Cable? (B&H#TECU8015ORG)

A: Yes

Q: 2. Will this work with a Nikon D850?

A: The Nikon D850 does not have a full USB port on the camera body. The TetherPro USB 2.0 Active Extension Cable (16', Black) would not work as the USB is full sized and not mini USB.

Q: 3. will this IR work on a Harman Kardon avr 320-i can't find an HE 1000 that is recommended?

A: I would think so, John. The original remote (or multi-function remote programmed by the original or downloaded IR codes) should pass right thru and into the IR receiver window on the front panel. Make sure that you have a power supply and connecting block to use this emitter

Q: 4. Can this shelf be installed in a Chatsworth QuadraRack 4-post frame?

A: Yes, the APC Fixed Shelf for NetShelter and Other 19" Racks (250 lb Rated, 1 RU) can be installed into a Chatsworth QuadraRack 4-post frame.

Q: 5. I bought this a few months ago. unfortunately did not have to use it until now. When I plug it in to the computer , the software does not recognize the camera. it doesn't know the camera was just plugged in. However, if I use only the USB cord that came with the camera it works. What is going on ? I have a Canon 5D-MII and using Canon software that came with the camera to tether.

A: I use this cord with a nikon D610 and if it is detached during capture I will have turn off the camera and the capture software plug the cord back in the start the Nikon capture software then turn on the camera after the program is up. you could try testing the cord on another camera.

Q: 6. is this the chord i want for the A7 or the male end?

A: Which a7? Either way, this is just the extension cable and will not fit in your device. You will want the male end, just make sure your camera has the correct USB3 port.

Q: 7. When looking at the 32 ft extension, it shows two chords in the photo. I don't want to assume anything, so is the 32ft basically two 16ft extensions or is it one long 32ft chord?

A: Hi it's two 16ft

Q: 8. Is this cable still needed when shooting tethered thru a powered dock, like a Caldigit TS3 Plus or OWC Thunderbolt 3? Or would it be redundant/overkill since the dock is providing an active connection?

A: Yes in that case it would likely not be needed.

Q: 9. Will this work with canon r5

A: This is a extension cable. It can be used to lengthen a USB cable past the normal limits.

Q: 10. does this require a battery?

A: The Tether Tools 16' Active Extension Cable doesn't require a battery to operate.