Corner Mount Flat Panel Tv

[Aluminum, Steel] I needed this wall mount for a corner installation for a flat panel 28 HDTV. It's perfect for my needs and was easily installed by myself in 10 minutes. (Didn't even need the enclosed instructions!)

[Landscape] Used this bracket to mount a 32 flat screen TV on a wall near a corner. Very easy to attach to both the back of the TV and the wall.Adjusts easily in virtually any direction.Includes necessary hardware for most situations. Solid construction.

[1] This is an excellent slim mount for your flat panel tv. Comes with all the needed hardware to put it on the wall. I had it up in a half hour with no trouble at all. My TV is a Sony 46. It is a 68lb Monster but it just hangs on the wall with no trouble at all. Of course, you have to make sure you screw it into the studs. I like the flip up ability that this mount has. Pull two little cords hanging just beneath the bottom of the mount and the bottom of the TV can be pulled away from the wall. Two braces flip out and keep the bottom of the TV about 4-5 away from the wall so you can access the cord jacks. I would recommend it to any looking for a flat mount.

[Black] Wall Mount works perfectly with corner mount bracket or on flat surface for excellent camera coverage!

Wall Mount works perfectly with corner mount bracket or on flat surface for excellent camera coverage!

[1x HDMI Female] The perfect finishing touch for a tight place behind the new flat-panel tv in our sanctuary.

[3.5" (8.9 cm)] I own a small home studio and I'm in the process of completing acoustic treatment in the room. I decided to mount a distant ribbon mic high in the far corner of the room. To tame frequencies in that corner I built a 1' X 1' X 2 acoustic panel with 703 insulation, a wood frame and FR701 fabric. Rather than hang this panel I wanted to do a rigid mount from the ceiling. I had a number of Matthews MicroGrip arms and clamps but I needed two mounts: one for the ceiling and one for the back of the panel. The CAMVATE Mounts are a lifesaver! They allowed me to do the rigid mount that I envisioned. Of course you can't do pull ups on this, but the MicroGrip hardware allows me to angle and articulate the exact placement of the panel in a solid manner.

[7 x 0.2 x 0.1"] I own a small home studio and I'm in the process of completing acoustic treatment in the room. I decided to mount a distant ribbon mic high in the far corner of the room. To tame frequencies in that corner I built a 1' X 1' X 2 acoustic panel with 703 insulation, a wood frame and FR701 fabric. Rather than hang this panel I wanted to do a rigid mount from the ceiling. I had a number of Matthews MicroGrip arms and clamps but I needed the two CAMVATE mounts and a shorter 6-inch MicroGrip rod to complete the installation. The CAMVATE Table Mounts and MicroGrip hardware allowed me to do the exact rigid mount that I envisioned. Of course you can't do pull ups on this, but the MicroGrip hardware allows me to angle and articulate the exact placement of the panel in a solid manner.

I own a small home studio and I'm in the process of completing acoustic treatment in the room. I decided to mount a distant ribbon mic high in the far corner of the room. To tame frequencies in that corner I built a 1' X 1' X 2 acoustic panel with 703 insulation, a wood frame and FR701 fabric. Rather than hang this panel I wanted to do a rigid mount from the ceiling. I had a number of Matthews MicroGrip arms and clamps but I needed two mounts: one for the ceiling and one for the back of the panel. The CAMVATE Mounts are a lifesaver! They allowed me to do the rigid mount that I envisioned. Of course you can't do pull ups on this, but the MicroGrip hardware allows me to angle and articulate the exact placement of the panel in a solid manner.

I own a small home studio and I'm in the process of completing acoustic treatment in the room. I decided to mount a distant ribbon mic high in the far corner of the room. To tame frequencies in that corner I built a 1' X 1' X 2 acoustic panel with 703 insulation, a wood frame and FR701 fabric. Rather than hang this panel I wanted to do a rigid mount from the ceiling. I had a number of Matthews MicroGrip arms and clamps but I needed the two CAMVATE mounts and a shorter 6-inch MicroGrip rod to complete the installation. The CAMVATE Table Mounts and MicroGrip hardware allowed me to do the exact rigid mount that I envisioned. Of course you can't do pull ups on this, but the MicroGrip hardware allows me to angle and articulate the exact placement of the panel in a solid manner.