Drill Bit Drawer Organizer Home Depot

[Front] Go to your garage and get your drill. Use a very small bit--up to you. Drill 2 holes about 5 or 6 mm apart close to the edge of the cap. Breakdown and spend 3 or 4 dollars for a lanyard (for sale here at B&H) thread it and your good to go! I've done this to every cap on every lens I own---it works!!

[Latch] I didn't use the divider kit in a Pelican case, but rather as an organizer for my camera gear in an existing drawer. The flexibility of the kit really allowed me to get everything exactly as I wanted.

[Folding] Purchased at Home Depot for 20 bux. Was intrigued by the assisted opening. It’s not really ‘spring assisted’ like a lot of knifes claim to be. It’s something else entirely, but whatever it is, this thing is fast. Blink of an eye fast. Not a fan of nylon grips, but dang it man this knife is quick. Blade locks open to which is another feature I really like. At this price point you cannot lose. If they gave you the option to upload a video, lots of folks would be surprised.

[1-1/8", 25 mm] I had to use a thiner pole then it's made to be used with, and it worked perfectly. I combined 2 10ft pipes from Home Depot and hung a 4x6 bounce off a 3 story drop. It was the moonlight effect I always wanted!!!

[E26] The main strength of these bulbs is that you get 500 watt power that you can plug into a conventional socket. No heavy betweenie, no Home Depot stadium lights. A lot of low budget filmmakers wonder where to go after you've graduated from the Home Depot light set. This is your next step up before professional level lighting.Warning, these are incredibly hot bulbs. They do not have a long life. Also DO NOT move the light while it is on or it will burn out.The $ each your paying is so that you don't have to buy a $ professional kit. It is what it is.

[19.2 lb] It's a drawer.

[3.5 lb (1.6 kg)] Work well. Needed to modify length a bit, and worked well. Had to cut and drill new holes with perfect outcome.

Work well. Needed to modify length a bit, and worked well. Had to cut and drill new holes with perfect outcome.

[0.57 lb] This TV mount came well packaged and it of excellent build quality, not much more to be desired at this price point. The instructions were clear and all the mounting hardware needed was included, except for the 1/4 in drill bit. Do note that the hole needs to be 3.5 in deep in order to accommodate the beefy bolts they provide in the kit. The drill bit I had was barely adequate and I needed to back it out of the chuck to finish the hole to the right depth. The unit installed without issues and feels extremely solid. The movements are firm but smooth. Very pleased with the results. I am using it for a 40 TV though so it's not putting much stress on the hardware.

[Black / Red] Provides a tight, securely locked connection with the female powerCon connecter. I use these to power network equipment installed in a Pelican case. Neutrik has CAD dxf and pdf drawings on their site if you need to drill holes in a surface for installation. I used their drawings to make a 3D printed stencil/jig for this purpose. For the screw holes, I use a 1/8 drill bit for machine screws w/ nuts, but go smaller if using a pointed/self-tapping screw. For the main entrance hole, I start with a 1/8 bit for a pilot hole, widen it with a 1/2 bit, then finally bore it all the way out with a 22mm step bit which makes a perfectly sized hole for this connector. For screws, M3 countersink (90deg) are an exact flush fit in the connector housing. I use black oxide screws to match the connector. The backside conductor tabs snap right into female quick connect terminals. I use the heat-shrink solder terminals and they stay on pretty well. If you need it to be really secure, consider soldering the terminals onto the tabs , but be careful not to melt the plastic!