Intel R Ethernet Server Adapter I350 T2

[ PCIe 3.0 x4] This RealTek GB NIC works great in our older DELL PowerEdge 2850 server!! We needed to replace an Intel Pro/1000 MT GB server adapter that went bad and bought another Intel GB adapter but the server would/could NOT recognize the new Intel NIC. Tried everything to remove the installed Intel NIC driver so it would take the new Intel NIC but the Intel NIC just would not be recognized - driver would not install correctly. The SOLUTION was to install the RealTek GB NIC card (non-Intel NIC). The RealTek NIC was recognized by the server upon bootup. I updated the RealTek driver that was installed by Windows Server 2003 using the CD that came with the NIC card. It worked with no problem. Am going to team two of them in the server later. Note: Make sure you update any driver installed automatically by your computer, itself, with the CD driver.

[Integrated] Among several NUC's at home, I replaced a 5th gen NUC with this 13th gen model. It serves as a media center for my music and photo collection, hence the 1 TB SSD and 16 GB memory. For those unfamiliar with the Intel NUC product line, they are small (4x4), very quiet, well-engineered and supported by a three-year warranty. Over the years, I have installed dozens for customers and not a single one has failed so far. The performance is impressive. The clip that keeps the power cord from inadvertently being yanked out is a fairly recent and useful addition. Intel has excellent documentation (assembly instructions, product specs) that I recommend. During installation of Windows 11, neither the wired Ethernet nor the Wi-Fi adapter were recognized which required an Ethernet-to-USB adapter. Others may add the network drivers during installation. Installing the Intel Driver & Support Assistant gets the optimal BIOS, firmware and drivers in place. Now that Intel has sold the NUC line to Asus, I hope that they will continue the development and support of this great product.

[Cat 6] Not much to say, it's a USB to Ethernet adapter. Works exactly like you would want it to.

[0.115 lb] [This review was collected as part of a promotion.] The Belkin USB-C to Ethernet + Charging adapter is amazing tool to have with you when you need an ethernet connection. The USB-C to Ethernet + Charging adapter charges your connected device while also providing an ethernet connection, so no need for multiple connectors. I have been using this on my Android phone and my laptop, both devices have a USB-C port and my Belkin adapter worked great on both devices. It provided an adequate charge and a stable internet connection without any issues. The adapter was immediately recognized by both devices and there was no need to install any software to make the adapter work. The adapter is also small and portable enough to carry with you anywhere you go. I would highly recommend this adapter to anyone looking for an ethernet + charging adapter.

[0.15 lb] works great, does not heat up as much as other ethernet adapter I've had.

[Bus Powered ] I always take my multiport adapter with me whenever I'm traveling. Super handy especially the ethernet port.

[1S] Intel the best

[Dovetail ring] I recently purchased a Nexstar C5. I wanted to replace the 1 1/4" Visual back adapter and supplied diagonal. The Baader Short T adapter allows the use of the Baader T2 prism on this telescope. This combination has full clearance from the drive base at zenith. Some thing that you have to be very careful of when you replace any of the optical path with larger or better products. It also allows for clearance when the Celestron Wi-Fi adapter is inserted into the base. For the smaller nextar mounts the adapter is almost directly under the telescope but at an angle. The combination of this T adapter with the prism is very efficient tight and requires no set screws. It absolutely looks like how this mounting should've been done originally. Please note that the prism is the smallest T2 diagonal that Baader makes with the 32 mm clear light path. And normally comes equipped with an 1 1/4" nose piece on one side and an 1 1/4" eyepiece holder with helical fine focuser on the other. Simply unscrew the nosepiece from the prism and replace it with this short T adapter. There are larger diagonals with both mirror and prism in the Baader line and I cannot vouch for clearance with those models.

[0.25 lb] This adapter is a great product that allows me to easily use my Nikkor lenses on my Fuji X-T1 and X-T2. Since there are no electrical connections, you must focus manually and VR is not available - but it provides some great flexibility without requiring the purchase of new lenses. One thing of note, is to ensure your Fuji camera is set to allow Shoot without Lens.

[0.355 lb] Very nicely made adapter with proper fit to Leica SL series cameras. I purchased this to connect my SL2-S to an astronomical telescope focuser using a 2 nosepiece. What I learned upon receipt is the difference between M2 (1.0mm thread pitch) and T2 (.75mm thread pitch)... most astronomical fittings are T2 and will not attach properly to M42 without an M2-T2 adapter. These exist but are not easy to find. Fortunately I did source one and the adapter now works perfectly for my intended use.